Why Gas Fees Spike During a Swap and How to Time It Better
Gas fees spike during a swap because Ethereum transaction fees are determined by network congestion, not by the swap itself. When many users compete to have their transactions mined at the same time, the gas price you must pay to get included in the next block rises. Swaps are especially vulnerable because they are time-sensitive: a pending swap that takes minutes to confirm can suffer severe slippage or fail entirely, so users often overpay for speed.
How Ethereum Gas Works in a Swap
Every swap on MilkshakeSwap is an Ethereum transaction that calls a smart contract function. The gas you pay has two components:
- Gas units: a fixed amount of computational work the swap requires (roughly 100,000 - 200,000 units for a simple token swap, more if it interacts with multiple pools or complex tokens).
- Gas price: the amount you pay per unit, measured in gwei (1 gwei = 0.000000001 ETH). This is the variable part.
The total gas fee = gas units × gas price. When you see a spike, it is the gas price rising because the Ethereum mempool is crowded. The swap itself does not create the spike - demand for block space does.
Why swaps see the sharpest gas spikes
Swaps have characteristics that make them expensive to confirm during congestion:
- Time sensitivity: A swap quoted at one price on submission may be stale within 30 seconds. If your transaction sits pending through several blocks, the price in the pool shifts, and your transaction may revert with "insufficient output amount" or execute at a worse rate than expected.
- Front-running risk: Bots monitor the mempool for pending swaps. If your swap moves the price significantly, a bot can insert a buy order ahead of yours and sell immediately after, extracting value (a sandwich attack). High gas prices are one defense - bots pay high fees too, so you must outbid them.
- Aggregator complexity: If you use an aggregator (covered elsewhere on this site), your transaction may call multiple pools. More contract calls mean more gas units, amplifying the effect of a high gas price.
How to Time a Swap to Avoid High Gas
You cannot control network congestion, but you can observe patterns and act accordingly.
1. Check the current gas price before submitting
Tools like Etherscan’s Gas Tracker or your wallet’s gas estimator show the current base fee and priority fee. Look for times when the "fast" gas price is below 30 - 50 gwei. This usually happens on weekends, late at night (UTC), or during low-activity periods in Asia and North America.
2. Wait for a lull in activity
Major token launches, NFT mints, or protocol upgrades cause gas spikes. Avoid swapping within an hour of a popular event. Similarly, avoid swapping during peak DeFi hours (typically 14:00 - 20:00 UTC when U.S. and European traders overlap).
3. Use the "advanced" gas options in your wallet
Most wallets let you set a custom gas price. Instead of using the "fast" preset, set a gas price that is 10 - 20% above the current base fee. This is usually enough to get included in the next few blocks without overpaying. The trade-off: your swap may take 1 - 3 minutes instead of 15 seconds.
4. Set a realistic slippage tolerance
A low slippage tolerance (e.g., 0.1%) combined with high network congestion increases the chance your swap fails because the price moves before your transaction lands. During busy periods, set slippage to 1 - 3% (or more for volatile tokens) to reduce failure risk. This does not lower gas, but it avoids paying gas on a failed transaction.
5. Avoid swapping during "gas wars"
When a popular token just launched or a major pool rebalances, gas spikes can exceed 500 gwei. During these events, even a simple swap may cost $50 - $100 in fees. Wait at least 2 - 4 hours after the initial frenzy. Check the pool’s liquidity depth - if volume is abnormally high, delay.
What to do if you must swap during high gas
If you cannot wait:
- Use a DEX on a layer-2 network (like Arbitrum or Optimism) where gas is a fraction of Ethereum mainnet. MilkshakeSwap may have deployments there; check the site.
- Use a limit order (if supported) that executes only when the gas price drops below a threshold you set.
- Accept that the fee will be high. Do not reduce the gas price to "slow" to save money - your swap may sit pending for hours and eventually revert, costing you the gas anyway.
The one thing that does not help
Manually setting the gas price to "slow" (the minimum) is rarely a good strategy for swaps. Unlike a simple ETH transfer, a swap has a time limit. If the network stays congested for 10 minutes, your swap may fail, and you lose the gas you paid. It is usually better to wait until gas is naturally low than to try a low-fee swap during a spike.
Summary
Gas spikes during swaps because many users want confirmation at the same time, and swaps are more time-sensitive than simple transfers. The best timing is when the mempool is quiet - typically weekends or late-night UTC. If you cannot wait, accept higher fees or switch to a layer-2 network. Do not try to outsmart the market by setting a low gas price during congestion; that leads to failed swaps and wasted fees.
Not financial advice. milkshakeswap.finance publishes market data and general information about MilkshakeSwap Token. Crypto assets are volatile and you can lose everything you put in. Nothing here is a recommendation to buy, sell or hold, and we make no price predictions.
Prices are sourced from third parties and may be delayed or wrong. Verify anything you intend to act on against a primary source.